歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-新聞資訊

新聞資訊

單工位旋轉噴淋清洗機的基本維護方法

作者：admin來源：http://www.heqingliang.cn/時間：2022-11-21

為了保證單工位旋轉噴淋清洗機在使用中所受到的損害小化并延長機器的使用壽命，這里小編為您介紹了清潔機的清洗保養方法，供您參考。

In order to minimize the damage to the cleaning machine in use and extend the service life of the machine, here we introduce the cleaning and maintenance methods of the cleaning machine for your reference.

1.保持工作場所清潔、干燥和通風。有利于設備的工作環境，長期高效運行。

1. Keep the workplace clean, dry and ventilated. It is conducive to the working environment of the equipment and long-term efficient operation.

2.電氣控制箱和設備通風口應遠離灰塵、水蒸氣和腐蝕性氣體，并定期用壓縮空氣清潔灰塵。

2. The electrical control box and equipment vent shall be far away from dust, water vapor and corrosive gas, and the dust shall be cleaned regularly with compressed air.

3.定期檢查單工位旋轉噴淋清洗機設備的絕緣性能，定期檢查老化的電氣元件，檢查地線，確保設備接地良好。

3. Regularly check the insulation performance of the equipment, the aging electrical components and the ground wire to ensure that the equipment is well grounded.

4.當清洗液太臟時，應及時處理，定期清洗儲罐并清洗罐內污垢，保持罐內和罐外清潔，可提高清洗罐內的耐久性。

4. If the cleaning solution is too dirty, it should be handled in time. The tank should be cleaned regularly and the dirt inside the tank should be cleaned to keep the inside and outside of the tank clean, which can improve the durability of the tank.

5.有過濾裝置的設備，應定期更換濾芯。

5. For equipment with filtering device, filter element shall be replaced regularly.

6.確認設備的電源電壓滿足要求，定期檢查電源，避免長時間在不穩定電源下工作。

6. Confirm that the power supply voltage of the equipment meets the requirements, and check the power supply regularly to avoid working under the unstable power supply for a long time.
單工位旋轉噴淋清洗機

7.對于有傳動機構的，應按要求定期加注潤滑油、黃油等潤滑油，并定期更換減速機齒輪油，以保證運動部件的平穩運行。

7. For those with transmission mechanism, lubricating oil such as lubricating oil and butter shall be added regularly as required, and gear oil of reducer shall be replaced regularly to ensure smooth operation of moving parts.

8.不要從超聲波控制柜頂部的進口處濺出導電液體。否則會嚴重?fù)p壞清洗設備的電路系統。

8. Do not splash conductive liquid from the inlet on the top of the ultrasonic control cabinet. Otherwise, the circuit system of the cleaning equipment will be seriously damaged.

9.避免單工位旋轉噴淋清洗機機器劇烈震動或碰撞。

9. Avoid violent vibration or collision of the machine.

10.機器連續運行時間應小于4小時。如果超過這個時間，須將超聲波調節旋鈕轉到“0”位置，讓風機繼續冷卻。

10. The continuous operation time of the machine shall be less than 4 hours. If this time is exceeded, the ultrasonic adjusting knob must be turned to the "0" position to allow the fan to continue cooling.

11.對于長時間運行的清洗機，停機前將電源旋鈕調至零，風機工作5分鐘后關閉，以確保電源內部的熱量被散發。

11. For the washing machine running for a long time, set the power knob to zero before shutdown, and turn off the fan after working for 5 minutes to ensure that the heat inside the power supply is dissipated.

12.定期運行油泵，每次至少10分鐘。

12. Run the oil pump regularly for at least 10 minutes each time.

13.用完后，用蓋子蓋上，防止潮濕和灰塵。

13. After use, cover it with a cover to prevent moisture and dust.

以上內容是清洗機的基本維護方法。無論什么機器，都需要精心維護，以確保使用效率。欲了解更多相關類型的清洗機信息，請關注我們網站www.heqingliang.cn進行咨詢吧！

The above contents are the basic maintenance methods of the cleaning machine. No matter what machine, it needs careful maintenance to ensure the efficiency of use. For more information about related types of washers, please visit our website www.heqingliang.cn for consultation!

上一篇：低溫廢水回收設備使用時的三個“避免”
下一篇： CNC高壓清洗機日常操作與使用說明