目前，市場上的許多超聲波振蕩器都使用大型水質凈化設備和超聲波清洗機。它可以用超聲波中的止溶液攪拌，清潔和消毒所需物品。超聲波清洗機中的超聲波振蕩器需要注意哪些問題？

At present, many ultrasonic oscillators on the market use large water purification equipment and ultrasonic cleaning machines. It can be used to stir, clean and disinfect the articles needed by the ultrasonic solution. What problems should be paid attention to in the ultrasonic oscillator of the ultrasonic cleaner?

一注意液位標準（低于標準勿開機）

I. Pay attention to the liquid level standard (do not start the machine if it is lower than the standard)

由于超聲波振蕩器的清洗槽容量不同，所以對于液位的要求也有一定的差別，在使用超聲波振蕩器前要認真閱讀說明書，詳細了解低槽深、液位深度，在液位未達標的情況下或者無液情況下切勿連接電源，這樣可能會對振蕩器造成損壞。

Due to the different capacity of the cleaning tank of the ultrasonic oscillator, the requirements for the liquid level are also different. Before using the ultrasonic oscillator, carefully read the instructions, understand the low tank depth and the liquid level depth in detail, and do not connect the power supply when the liquid level is not up to the standard or there is no liquid, which may cause damage to the oscillator.

二注意清洗劑種類（勿選擇腐蝕類產品）

II. Pay attention to the type of cleaning agent (do not choose corrosive products)

超聲波振蕩器可以使用純水等進行清洗，同時也可以使用水加清洗劑進行清潔效果更佳，針對不同的工件而言，清洗劑的選擇要尤為注意。首先清洗劑不可以對振蕩器本體造成腐蝕或損害，同時也要滿足工件的清洗要求，要注意溫度對于清洗劑的性狀改變情況，一些清洗劑耐溫性較差，經高溫后可能會腐蝕振蕩器，所以要避免使用此類清洗材料。

The ultrasonic oscillator can be cleaned with pure water, etc. At the same time, it can also be cleaned with water and detergent. For different workpieces, the selection of detergent should be paid special attention. First of all, the cleaning agent can not cause corrosion or damage to the oscillator body, but also meet the cleaning requirements of the workpiece. Pay attention to the change of the properties of the cleaning agent due to the temperature. Some cleaning agents have poor temperature resistance and may corrode the oscillator after high temperature, so avoid using such cleaning materials.

三注意溫度峰值（峰值時禁止人工開機）

III. Pay attention to the peak temperature (it is forbidden to start the machine manually at the peak)

絕大部分高品質的超聲波振蕩器都設有自我保護功能，這樣可以保護設備自身安全，當使用較長時間后振蕩器內部溫度便會成倍增長，此時設備自動探溫系統便會發出信號，使設備立即停機，處于休眠狀態。此時禁止人工開機，以免排熱不暢導致設備的永久性損壞。

Most high-quality ultrasonic oscillators are equipped with self-protection function, which can protect the safety of the equipment. When used for a long time, the internal temperature of the oscillator will multiply. At this time, the automatic temperature detection system of the equipment will send a signal to stop the equipment immediately and put it in sleep. At this time, it is forbidden to start the machine manually to avoid permanent damage to the equipment due to poor heat removal.

四注意內槽清潔（防止影響下批工件）

IV. Pay attention to the cleaning of the inner groove (prevent affecting the next batch of workpieces)

一般來說的超聲波振蕩器工作頻率不宜太過頻繁，間歇式工作，要注意將內槽進行清潔，避免工件中的污垢腐蝕內膽，同時也避免清洗劑對于其它工件產生影響。所以從原則上來說，不同類型的工件使用不同的超聲波振蕩器清洗劑后，要將內槽內液排出后進行清洗，再清洗下一波工件。

Generally speaking, the working frequency of professional ultrasonic oscillator should not be too frequent. For intermittent operation, pay attention to cleaning the inner groove to prevent the dirt in the workpiece from corroding the inner liner, and also avoid the impact of cleaning agent on other workpieces. Therefore, in principle, after using different ultrasonic oscillator cleaning agents for different types of workpieces, the liquid in the inner tank should be discharged and cleaned before cleaning the next wave of workpieces.

同時還要注意振蕩器使用完成后要及時的關閉開關，并且將電源拔下，將電源長期停留于排線孔中也會加速其老化，而且可能還會引發危險。同時要注意將超聲波振蕩器沖洗完成后，好可以使用吸水布將水分清除，這樣可以延長振蕩器的使用壽命。更多相關使用就來咨詢我們http://www.heqingliang.cn吧！

At the same time, pay attention to timely turn off the switch after the oscillator is used, and unplug the power supply. If the power supply stays in the cable hole for a long time, it will also accelerate its aging, and may cause danger. At the same time, it should be noted that after the ultrasonic oscillator is washed, the water can be removed with absorbent cloth, which can prolong the service life of the oscillator. Consult us for more information http://www.heqingliang.cn Come on!