CNC高壓清洗機設備在我們的生活和工業生產中都發揮著十分重要的作用，不少清潔公司和工廠都會使用到這類設備，很多人在使用設備的時候遇到壓力不足、噴頭不出水等問題不知道該如何解決。下面小編就為大家介紹一下CNC高壓清洗機常見問題的解決方法。

CNC high-pressure cleaning machine equipment plays a very important role in our life and industrial production. Many cleaning companies and factories will use this kind of equipment. Many people do not know how to solve the problems such as insufficient pressure and no water from the nozzle when using the equipment. Now, Yangzi Xiaobian will introduce solutions to common problems of CNC high-pressure washer.

1、CNC高壓清洗機壓力不穩定：

1. The pressure of CNC high-pressure washer is unstable:

設備出現壓力不穩定的情況一般是因為高壓水泵或者進水管路中吸入了空氣所導致的，需要我們檢查水源的壓力是否足夠，進水過濾器是否堵塞，當發現過濾網堵塞時，及時的進行清洗，晾干以后使用就可以了。

The unstable pressure of the equipment is generally caused by the intake of air from the high-pressure water pump or the water inlet pipe. We need to check whether the pressure of the water source is sufficient and whether the water inlet filter is blocked. If the filter screen is blocked, clean it in time and dry it before use.

2、運行過程中出現異響：

2. Abnormal noise during operation:

設備出現異響一般是由于電機軸承缺油所導致的，遇到這類問題時在電機的注油孔注入普通黃油就可以了，一般這種情況發生的不多，我們在日常使用過程中做好定期的維護和檢查就可以了。

The abnormal noise of the equipment is generally caused by the lack of oil in the motor bearing. In case of such problems, it is OK to inject ordinary grease into the oil injection hole of the motor. Generally, this kind of situation does not occur much. We can do regular maintenance and inspection in the daily use process.

3、使用后設備壓力降低：

3. The pressure of the equipment decreases after use:

遇到這個問題我們首先要檢查高壓噴嘴是否出現嚴重磨損的情況，普通壓力的CNC高壓清洗機噴嘴基本不會出現磨損的情況，但是一些超CNC高壓清洗機設備在運行過程中會進行過熱處理，比較容易出現磨損的情況。遇到這類情況要注意檢查調壓閥和水泵內部的密封組件。

When encountering this problem, we should first check whether the high-pressure nozzle is seriously worn. The nozzle of the ordinary pressure CNC high-pressure washer will not be worn, but some super CNC high-pressure washer equipment will be overheated during operation, which is more prone to wear. In such cases, pay attention to check the pressure regulating valve and the sealing components inside the water pump.

4、高壓水槍不出水：

4. No water from high-pressure water gun:

當調壓閥壓力正常而高壓水槍卻不出水，或者是噴嘴噴射的水流不規則、分散的時候，說明高壓水槍內出現了異物堵塞的情況，要及時的清理噴嘴。

When the pressure of the pressure regulating valve is normal but the high-pressure water gun does not discharge water, or the water jet from the nozzle is irregular and dispersed, it indicates that there is a blockage of foreign matters in the high-pressure water gun, and the nozzle should be cleaned in time.

5、水泵底部漏油：

5. Oil leakage at the bottom of water pump:

CNC高壓清洗機水泵底部漏油主要是由于泵內油封損壞，遇到這類情況我們要及時的更換油封；當水泵在運轉過程中，曲軸和連軸不停的做往返運動，這時主要靠油給設備進行潤滑和降溫，所以水泵在使用過程中不能缺少潤滑油。

The oil leakage at the bottom of the water pump of the CNC high-pressure washer is mainly due to the damage of the oil seal in the pump. In this case, we should replace the oil seal in time; When the water pump is running, the crankshaft and coupling keep moving back and forth. At this time, oil is mainly used to lubricate and cool the equipment, so the water pump cannot be short of lubricating oil during use.

以上這些問題我們在使用過程中很可能會遇到，其實只要在使用CNC高壓清洗機的過程中做好維護和保養工作，就能在一定程度上避免許多問題，特別是由于配件問題導致的故障。更多相關使用問題或者購買問題就來我們網站www.heqingliang.cn咨詢了解吧！

We are likely to encounter the above problems in the process of use. In fact, as long as we do a good job of maintenance and servicing in the process of using the CNC high-pressure washer, we can avoid many problems to a certain extent, especially those caused by parts problems. For more questions about use or purchase, please visit our website www.heqingliang.cn!