隨著超聲波清洗機設備的應用范圍越來越廣泛，各種經過不斷完善和改進的清洗設備正在取代已面市的老式設備，通過式噴淋清洗機為大多數人所接受并受到歡迎，下面小編來講講它具體的操作工藝流程是怎樣的。

With the application scope of ultrasonic cleaning machine equipment becoming more and more extensive, various cleaning equipment that has been constantly improved and improved are replacing the old equipment that has been put on the market. The through type spray cleaning machine is accepted by most people and is welcomed. The following section will talk about its specific operation process.

通過式噴淋清洗機所采用的通過式清洗技術采用頻率28KHz的超聲波進行清洗，由噴淋系統、噴嘴旋轉裝置、磷化系統、自動溫控加熱系統、風切吹水系統等組成。對于某些特定的清洗對象，還配有熱空氣烘干、專用清洗架及清洗液的過濾循環系統。

The pass through cleaning technology adopted by the pass through spray cleaning machine adopts the ultrasonic wave with a frequency of 28KHz for cleaning, which is composed of the spray system, nozzle rotating device, phosphating system, automatic temperature control heating system, air cutting and water blowing system, etc. For some specific cleaning objects, it is also equipped with hot air drying, special cleaning rack and filtering circulation system of cleaning solution.

通過式噴淋清洗機工作時，將料框置于輸送帶上，清洗工件裝于相對應的料框中，零件不得重疊，節拍為2-3min/筐；料筐依次通過清洗室、漂洗室、吹干、烘干室，完成全過程后自動輸出清洗潔凈的零件，如有水珠需進行人工補吹，將吹干后的零件放入防塵周轉箱。

When the through type spray washer works, place the material frame on the conveyor belt, and put the cleaning workpiece in the corresponding material frame. The parts shall not overlap, and the beat is 2-3 min/basket; The basket passes through the cleaning room, rinsing room, drying room and drying room in turn. After the completion of the whole process, the cleaned parts are automatically output. If there are water drops, manual blowing is required, and the dried parts are put into the dust-proof turnover box.

相比傳統的清洗設備，通過式噴淋清洗機的主要特點是不僅能有效的避免高光潔度物體的表面損傷；而且可除去附著在表面的亞微米大小的顆粒；甚至對浸入液體中，面向換能器的一面也能被洗凈，所以要進行兩面清洗。

Compared with the traditional cleaning equipment, the main feature of the through spray cleaning machine is that it can not only effectively avoid the surface damage of the high finish objects; And the submicron sized particles attached to the surface can be removed; Even for immersion in liquid, the side facing the transducer can be cleaned, so both sides should be cleaned.

通過式噴淋清洗機作業后，被清潔的零件不能停放在運送帶上，按中止按鈕，使全機中止運轉。清潔液應定時添加水和必定份額的金屬清潔劑以彌補耗費，使液面保持在必定高度，若是清潔作用達不到規則的技術需求時，應悉數替換清潔液。

After the operation of the through spray washer, the cleaned parts cannot be parked on the conveyor belt. Press the stop button to stop the whole machine. Water and a certain amount of metal cleaner shall be regularly added to the cleaning liquid to make up for the consumption, so as to keep the liquid level at a certain height. If the cleaning effect cannot meet the regular technical requirements, the cleaning liquid shall be replaced in full.

操作通過式噴淋清洗機的時候，注意要將被清潔的零件要規整地放在運送帶上，不許壓在滾輪上；而且在運送帶上，被清潔的零件不能堆得過多，避免影響清潔作用，每個零件都能清潔到。更多注意事項就來我們網站www.heqingliang.cn咨詢了解吧！

When operating the pass through spray washer, be careful to place the cleaned parts on the conveyor belt in a neat manner, and do not press them on the rollers; In addition, the cleaned parts shall not be stacked too much on the conveyor belt to avoid affecting the cleaning effect, and each part can be cleaned. For more information, please visit our website www.heqingliang.cn!