歡迎訪問濟南科爾超聲波設備有限公司網站！

專注生產工業用超聲波清洗機

讓工業清洗無難事

業務咨詢電話：

18663767799

你所在位置：首頁-新聞動態-常見問題

常見問題

造成KRDC系列多槽清洗機不加熱不升溫的因素

作者：admin來源：http://www.heqingliang.cn/時間：2022-07-09

KRDC系列多槽清洗機的加熱功能可以有效提高清洗效率，一般加熱功能只支持加熱到80攝氏度。如果再高一點，對清洗效果影響不大，80度已經達到了少量液體的沸點。任何更高將達到大多數液體的沸點。如果您購買的設備有加熱功能，但在使用過程中加熱功能失效，具體是什么原因？

The heating function of KRDC series multi tank cleaning machine can effectively improve the cleaning efficiency. Generally, the heating function only supports heating to 80 ℃. If it is higher, it will have little impact on the cleaning effect. 80 degrees has reached the boiling point of a small amount of liquid. Any higher will reach the boiling point of most liquids. If the equipment you purchased has heating function, but the heating function fails during use, what is the specific reason?

1、加熱膜與電路板的連接斷開；

1. The heating film is disconnected from the circuit board;

2、設定溫度低于實際溫度；

2. The set temperature is lower than the actual temperature;

3、加熱膜燒壞；

3. The heating film is burnt out;

4、控制面板溫度設置模塊無效。

4. The control panel temperature setting module is invalid.
超聲波清洗設備

導致KRDC系列多槽清洗機不升溫的因素有哪些？針對這些可能的原因，我們可以通過以下方式來判斷和處理。

What are the factors that lead to the non heating of KRDC series multi tank cleaning machine? For these possible reasons, we can judge and deal with them in the following ways.

1、檢查加熱膜與電路板連接的電路是否斷開。如果是這樣，您可以自己連接并再次測試；

1. Check whether the circuit between the heating film and the circuit board is disconnected. If so, you can connect yourself and test again;

2.當您設定的溫度低于液體的實際溫度時，加熱功能不開啟。可以查看自己設定的溫度，提高設定溫度來測試加熱功能是否正常開啟。

2. When the temperature you set is lower than the actual temperature of the liquid, the heating function does not turn on. You can check your set temperature and increase it to test whether the heating function is normally turned on.

3、加熱膜一般覆蓋在清洗槽的外表面，可以觀察是否燒壞。如果發熱膜燒壞，需要聯系超聲波清洗設備廠家更換維修。

3. The heating film is generally covered on the outer surface of the cleaning tank, and you can observe whether it is burnt out. If the heating film is burnt out, contact the manufacturer of ultrasonic cleaning equipment for replacement and maintenance.

4、如果排除以上原因，很有可能是控制面板的問題。

4. If the above reasons are eliminated, it is likely to be the problem of the control panel.

以上就是今天為大家介紹的關于問題以及注意事項的全部內容，希望對大家能有所幫助，想要了解更多內容可以電話聯系我們或者關注我們的網站www.heqingliang.cn，我們的工作人員會及時與您取得聯系。

The above is all about the problems and precautions introduced to you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website www.jnthcsb COM, our staff will contact you in time.

上一篇：定制生產通過式清洗設備的參數要求
下一篇：碳氫清洗機的幾個關鍵注意點