超聲波清洗機憑借其高效、便捷的清潔能力，已成為家庭和工業領域的必備工具。然而，想要讓設備長期穩定運行，日常維護與保養至關重要。今天，我們將為您詳細講解超聲波清洗機的維護技巧，并解答常見問題，助您輕松應對使用中的各種挑戰！

　　Ultrasonic cleaning machines, with their efficient and convenient cleaning capabilities, have become essential tools in both household and industrial fields. However, in order to ensure long-term stable operation of the equipment, daily maintenance and upkeep are crucial. Today, we will provide you with a detailed explanation of maintenance techniques for ultrasonic cleaning machines and answer common questions to help you easily cope with various challenges in use!

　　一、日常維護要點

　　1、 Key points of daily maintenance

　　小貼士：根據清洗對象選擇專用清洗劑，定期更換液體（如每周一次），并清潔槽內壁污漬。

　　Tip: Choose a specialized cleaning agent according to the cleaning object, change the liquid regularly (such as once a week), and clean the stains on the inner wall of the tank.

　　清洗液的選擇與更換：超聲波清洗機的清洗液直接影響清潔效果和設備壽命。建議使用中性或弱堿性清洗劑，避免強酸強堿液體腐蝕設備。每次使用后，需徹底排空殘留液體，防止沉淀堵塞換能器或管道。

　　Selection and replacement of cleaning solution: The cleaning solution of ultrasonic cleaning machine directly affects the cleaning effect and equipment life. It is recommended to use neutral or weakly alkaline cleaning agents to avoid corrosion of equipment by strong acid and alkali liquids. After each use, the residual liquid should be thoroughly drained to prevent sedimentation from blocking the transducer or pipeline.

　　避免空載運行：超聲波清洗機不可在無液體的狀態下啟動，否則可能導致換能器過熱或損壞。使用前確保液位覆蓋被清洗物品，且不超過最大容量。

　　Avoid no-load operation: The ultrasonic cleaning machine should not be started in a liquid free state, otherwise it may cause the transducer to overheat or be damaged. Before use, ensure that the liquid level covers the cleaned item and does not exceed the maximum capacity.

　　設備清潔與干燥：每次使用后，用軟布擦拭機身和槽體，保持通風干燥，防止水漬殘留導致電路受潮或金屬部件生銹。

　　Equipment cleaning and drying: After each use, wipe the body and tank with a soft cloth to maintain ventilation and dryness, and prevent residual water stains from causing the circuit to become damp or metal parts to rust.

　　二、常見問題處理

　　2、 Common problem handling

　　季節性維護建議：

　　Seasonal maintenance recommendations:

　　梅雨季：增加設備除濕頻率，使用防潮柜存放備用換能器。冬季：若環境溫度低于5℃，啟動前預熱清洗液至20℃以上，避免冷啟動損傷換能器。

　　During the rainy season, increase the frequency of equipment dehumidification and use moisture-proof cabinets to store spare transducers. Winter: If the ambient temperature is below 5 ℃, preheat the cleaning solution to above 20 ℃ before starting to avoid cold start damage to the transducer.

　　01振子受潮

　　01 The oscillator is damp

　　癥狀：絕緣電阻低于30兆歐，導致設備功率異常。處理：將換能器放入100℃烘箱烘干3小時，或用吹風機除潮至電阻值恢復。

　　Symptom: The insulation resistance is below 30 megaohms, resulting in abnormal power of the equipment. Solution: Place the transducer in a 100 ℃ oven and dry for 3 hours, or use a hair dryer to remove moisture until the resistance value is restored.

　　振動面穿孔原因：長期高負荷使用導致金屬疲勞。建議：定期檢查振動面完整性，發現穿孔立即停用并更換部件。

　　Reason for perforation of vibration surface: Metal fatigue caused by long-term high load use. Suggestion: Regularly check the integrity of the vibration surface, and immediately stop using and replace components if perforation is found.

　　02振子打火或陶瓷碎裂

　　02 Vibrator ignites or ceramic shatters

　　癥狀：肉眼可見裂紋或異響，絕緣性能下降。應急措施：斷開損壞振子的電路，避免影響其他振子，并及時聯系廠家更換。03振子脫膠

　　Symptoms: Visible cracks or abnormal noise, decreased insulation performance. Emergency measures: Disconnect the circuit of the damaged oscillator to avoid affecting other oscillators, and promptly contact the manufacturer for replacement. 03 oscillator debonding

　　癥狀：振動面效果減弱，可能伴隨異常噪音。預防：避免撞擊振動面；發現脫膠需返廠維修，不可自行粘合。

　　Symptom: Weakened vibration surface effect, possibly accompanied by abnormal noise. Prevention: Avoid hitting vibrating surfaces; If delamination is found, it needs to be returned to the factory for repair and cannot be self bonded.

　　三、延長設備壽命的保養技巧

　　3、 Maintenance techniques for extending equipment lifespan

　　超聲波清洗機作為一種精密設備，其使用壽命與日常保養密切相關。以下是一些實用的保養技巧，幫助您延長設備壽命，確保其高效運行：

　　As a precision equipment, the service life of ultrasonic cleaning machine is closely related to daily maintenance. Here are some practical maintenance tips to help you extend the lifespan of your equipment and ensure its efficient operation:

　　1. 定期檢查電路與絕緣性能

　　1. Regularly check the circuit and insulation performance

　　操作建議：每月使用兆歐表檢測換能器插頭的絕緣電阻（23腳間需大于30兆歐），確保電路安全。注意事項：若發現絕緣電阻下降，可能是振子受潮或損壞，需及時處理。

　　Operation suggestion: Use a megohmmeter to check the insulation resistance of the transducer plug every month (greater than 30 megohms between pins 23) to ensure circuit safety. Attention: If a decrease in insulation resistance is found, it may be due to moisture or damage to the oscillator, which needs to be dealt with in a timely manner.

　　2. 控制清洗溫度與時間

　　2. Control the cleaning temperature and time

　　溫度控制：根據清洗對象的材質設定合理溫度（通常≤60℃），避免高溫加速部件老化或損傷精密物品。時間控制：清洗時間一般控制在3-10分鐘，過長可能導致設備過熱或清洗液失效。

　　Temperature control: Set a reasonable temperature (usually ≤ 60 ℃) based on the material of the cleaning object to avoid high temperature accelerating component aging or damaging precision items. Time control: The cleaning time is generally controlled within 3-10 minutes. If it is too long, it may cause the equipment to overheat or the cleaning solution to fail.

　　3. 避免超負荷運行/清洗液管理與槽體清潔

　　3. Avoid overloading operation/cleaning solution management and tank cleaning

　　工業設備：嚴格按照額定功率使用，禁止同時清洗過多物品或過重部件，防止電機過載。家用設備：避免一次性清洗過多小物件（如珠寶、眼鏡），以免影響清洗效果和設備壽命。潤滑保養：每季度對傳動部件（如軸承）添加潤滑劑，減少摩擦損耗。緊固檢查：定期檢查螺絲是否松動，確保振動系統穩定性，避免因松動導致設備異常振動或噪音。清洗液選擇：使用中性或弱堿性清洗劑，避免強酸強堿液體腐蝕設備。槽體清潔：每次使用后徹底排空殘留液體，并用軟布擦拭槽體內壁，防止污漬堆積。

　　Industrial equipment: strictly use according to rated power, prohibit cleaning too many items or heavy components at the same time, and prevent motor overload. Household equipment: Avoid cleaning too many small items (such as jewelry and glasses) at once to avoid affecting the cleaning effect and equipment lifespan. Lubrication and maintenance: Add lubricants to transmission components (such as bearings) every quarter to reduce friction losses. Tightening inspection: Regularly check whether the screws are loose to ensure the stability of the vibration system and avoid abnormal equipment vibration or noise caused by looseness. Cleaning solution selection: Use neutral or weakly alkaline cleaning agents to avoid corrosion of equipment by strong acid and alkali liquids. Tank cleaning: After each use, thoroughly drain any remaining liquid and wipe the inner wall of the tank with a soft cloth to prevent the accumulation of stains.

　　用戶常見問題解答問：清洗機噪音突然變大，是什么原因？答：可能是振子脫膠或振動面穿孔，建議檢查并聯系售后維修。問：清洗效果變差，如何解決？答：檢查清洗液是否失效，或振子是否受潮、損壞，必要時更換部件。問：設備無法啟動，怎么辦？答：首先檢查電源連接是否正常，再排查電路板或換能器是否故障。

　　FAQ for Users: What is the reason for the sudden increase in noise from the cleaning machine? Answer: It may be due to the detachment of the oscillator or perforation of the vibration surface. It is recommended to check and contact after-sales maintenance. Q: How to solve the problem of poor cleaning effect? Answer: Check if the cleaning solution is ineffective, or if the oscillator is damp or damaged, and replace the components if necessary. Q: What should I do if the device cannot start? Answer: First, check if the power connection is normal, and then investigate if the circuit board or transducer is faulty.

　　總結超聲波清洗機的維護與保養并不復雜，只需從日常操作規范入手，結合定期深度檢查與針對性故障處理，即可顯著提升設備效率并延長使用壽命。若遇復雜故障（如振子脫膠或電路板損壞），建議聯系專業廠家維修，避免自行拆解導致二次損壞。希望這篇文章能幫助您更好地使用超聲波清洗機！如果您還有其他問題，歡迎留言，我們將為您一一解答！

　　The maintenance and upkeep of ultrasonic cleaning machines are not complicated. By starting with daily operating standards, combined with regular in-depth inspections and targeted troubleshooting, the equipment efficiency can be significantly improved and the service life can be extended. If encountering complex faults (such as oscillator detachment or circuit board damage), it is recommended to contact a professional manufacturer for repair to avoid secondary damage caused by self disassembly. I hope this article can help you better use the ultrasonic cleaning machine! If you have any other questions, please feel free to leave a message and we will answer them one by one for you!

　　本文由 超聲波清洗機  友情奉獻.更多有關的知識請點擊  http://www.heqingliang.cn/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from an ultrasonic cleaning machine For more related knowledge, please click http://www.heqingliang.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.